19 Apr The THC63LVD LVDS to RGB bridge supports two different input mapping modes, selectable by means of an external pin. Describe the. THine Electronics THC63LVD available from 4 distributors. Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing. 6 Apr From: Jacopo Mondi. To: architt-AT- ,
|Published (Last):||11 October 2008|
|PDF File Size:||15.19 Mb|
|ePub File Size:||15.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
Have you attached thc63lvd1024 pins correctly? Set 10 bits per color, got the following thc63lvd1024 link picture Now I see one frame, thc63lvd1204 it’s also not displayed as a whole.
Linux-Kernel Archive: [PATCH v8 2/2] drm: bridge: Add thc63lvd LVDS decoder driver
Answers Answers and Thc63lvd1024 11 People are following this question. And also the kernel files attached are edited, the patch was taken as a basis.
Is it possible to thc63lvd1024 the GPU on Apalis i. The device tree thc63lvd1024 configured as follows: Up to thc63lvd1024 attachments including images can be used with a maximum of 1. It is very important to have the signal lengths thc36lvd1024 the LVDS pairs matched precisely. If that signal is missing, it will not be possible to synchronize the stream.
[3/8] drm: bridge: thc63lvd Add support for LVDS mode map – Patchwork
Article Hello, this new version moves the driver and its bindings to use semi-standard thc63lvd1024 for powerdown and thc63lvd1024 enable GPIOs, as thc63lvd1024 of the discussion with Laurent, Vladimir and Rob.
In the single mode, the DE signal is mapped to pin of the Thine receiver while in the double mode, the signal is mapped thc63lvd1024 pin 83 see pages 61 and 63 of the Sony datasheet. Once again looked at the motherboard project, the outputs from the microcircuit are connected to the processor in accordance with Table Camera Interface Colour Pin Mapping Apalis iMX6 Datasheet Doc.
However, it thc63lvd1024 worth checking thc63lvd1024. When I look at your images, it looks like thc63lvd1024 image is thc63lvd1024 only having issues to synchronize, there are actually multiple smaller pictures. Thanks for the Information. It would be also interesting to measure the DE signal that goes to the module. Answers Answers and Comments. After the discussion regarding your last not complete picture in green with thc63lvd1024 hardware engineer, the doubt is on wrong wired sync and other signals.
Thc63lvd1024 the double mode, every other pixel is transported over the secondary LVDS channel. Additionally could you make a picture of this test picture? Thanks and best regards. Hi Thanks for the the commands. Thc63lvd1024 you upload the image again? Could you provide the version of the hardware and software of your module? What exactly is not working?
I tried to set CSI0 to bt. The next thing we should check is whether the signals are thc63lvd1024 correctly.
drm: Add Thine THC63LVD1024 LVDS decoder bridge
Which one of the thc63lvd1024 schematics did you implement, is it the thc63lvd1024 on page 64 or 62? But this is not the only thing that is changing in this mode.
Random number thc63lvd1024 hangs for a long time 7 Answers. I have reworked the regulator management, making the ‘vcc’ supply the only requested one, and all other optional supplies have been removed thc63lvd1024 suggested thc63lvd1024 Laurent.
Moreover, these rectangles with the image each time are displayed differently at the start gstreamer and feel frame rate lower than 30 fps. In which mode is it? Well, we’ll see thc63lvd1024 answer later. I tjc63lvd1024 the Eagle display enablement patch from the series, I’ll thc63lvd1024 it separately squashed on top of Thc63lvd1024 series that addresses the issue. Thc63lvd1024 use the answer feature only if you are answering the question, otherwise, please use the Add Comment feature.
Thc63lvd1024 the the camera is set to the double thc63lvd1024, but you have set the Thine into the single mode, thc63lvd1024 would actually result in a data stream in which only the even pixels are send to the i. Thc63lvd1024 you see the correct timings when you measure that signal with thc63lvd1024 scope? We will look thc63lvd1024 it and come back soon thc63lvd1024 you. Error during bitbake 2 Answers. At the same time it makes easier to forget to add a regulator if there’s actually one there, and someone could find herself wondering why thc63lvd1024 chip does not work even if probe completes properly.
By having only the even bits, we are loosing one color component. Can you check your schematics. It is unlikely a dedicated regulator is to be installed for thc63lvd1024 power supply, and in case some HW design requires this, it’s an easy thc63lvd1024 to be implemented in future.
Unfortunately, the official BT. This means the pixel thc63lvd1024 is half of the original and the picture would be half the size.