LM3900 PDF

LM LM LM Quad Amplifiers. General Description. The LM series consists of four independent dual input internally compensated amplifiers . Texas Instruments LM Series Operational Amplifiers – Op Amps are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . lm are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for lm

Author: Zurisar Zujind
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: History
Published (Last): 4 March 2010
Pages: 423
PDF File Size: 11.88 Mb
ePub File Size: 8.90 Mb
ISBN: 413-1-54367-349-4
Downloads: 15211
Price: Free* [*Free Regsitration Required]
Uploader: Tauk

Your email address will not be published. There is one set of power connections for the four amplifiers, lm300 they are otherwise independent. Calvert Created 10 August Last revised 19 September The capacitor charges until its voltage reaches this level, but then the ouput goes low and it begins to discharge again.

The input and supply voltages can be exchanged to give a noninverting circuit.

It relies on the diode drop at the inverting input to supply a current proportional to V bewhich is then amplified by the feedback resistor. Equal currents supplied to the two inputs are not amplified. It supplies a current 12 – 0.

Connections for the LM are shown at the left. By adding the same circuit parallel with this, you can increase the number of inputs according to the applications. Capacitors C1 to C4 are the decoupling capacitors for the corresponding channels. It looks like the same circuit for the usual op-amp, but here the resistors are necessary.

TOP Related Articles  AYYAPPA 108 SARANAM EBOOK

You may also like: The output terminal from each channel is connected to a single output line with a resistance not greater than K and produces a mixed audio at the output with very low noise. There is no common-mode voltage range at all! The measured values from the scope were 3. The first circuit to look at is the inverting amplifier, shown at the right. This is an AC amplifier, with coupling capacitors at input and output so there is no worry about DC bias levels, which can be chosen as necessary.

When you test this circuit, the scope traces for input and output can be superimposed with proper setting of the gain, and the inversion is obvious. Multi channel audio mixer circuit. To understand this circuit, assume for simplicity that the output swings from 0 to the supply voltage V.

The output goes from high to low when the input reaches 7 V, and from low to high when it goes below 6 V, with a hysteresis of 1 V. Hello, can I use 3.

A relaxation oscillator is shown at the left. The divider supplies a current into what is effectively a unity-gain buffer to reproduce its voltage at the output. An inverting Schmitt trigger is shown at the right.

National Semiconductor

C5 is the output decoupling capacitor. The input resistor turns the applied voltage into a current, while the feedback resistor causes the output to rise to a value lj3900 an equal current to the inverting input. The usual op-amp responds to a differential voltage at its inputs, but the LM responds to a differential current. LM pin configuration and architecture. The input and feedback resistors are as with the familiar circuit, and the gain in this case should be However, these op-amps are very different from the usual op-amp, and must be used in a completely different way.

TOP Related Articles  GNAS HANDICAP TABLES PDF

National Semiconductor – datasheet pdf

They also provide a large output swing. I think resistors R8 and R10 should be taken out. Connect Ch 1 to the lm3900 voltage, and Ch 2 to the output. It has been replaced by a common-mode current range by the current differencing. These are the trip levels expressed in currents.

Quad Amplifier | LM

The label “Norton” refers to the Norton equivalent circuit for a current source. The unity-gain buffer is a special case of the noninverting amplifier, shown at the right with biasing by means of a pm3900 divider.

The LM is specially useful when only a single power supply is available. The circuit consists of 4 channel quad amplifier LM Note the symbol for the Norton op-amp, that has a current source ml3900 the inputs, and an arrow on the noninverting input.

Instead of a differential amplifier, the input stage is the current-differencing circuit shown at the right. Again, the high input impedance of the voltage op-amp is not obtained.