Automatic Chain Drive/Belt Drive Garage Door Operator System Ownerâs Manual SAVE FOR FUTURE REFERENCE Customer Service. Overhead Door Garage Door Opener Owner’s Manuals. describe the image. The Overhead Door Legacy (model #/) garage door opener. CD Series Garage Door Opener pdf manual download. Also for: Cdb Garage Door Opener Overhead door legacy Programming And Operating Manual . CAUTION Line “V” “B” Header bracket must be fastened to garage fram- ing.
|Published (Last):||7 May 2010|
|PDF File Size:||12.37 Mb|
|ePub File Size:||11.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
If your door sticks, binds, or is out of balance, have it adjusted by a professional. Operator works from wallcontrol, but not fromremote control. Erase all remote control codes from receiver memory and reprogram. Attach wires to terminals Phantom Fig. Check the power source. Check the power source. Self-drilling screws are intended for use withlight-weight door only, while lag screws are meantfor wood doors only.
Tie overhand knot in end of cord. Make sure cover is on power head before operation. If permanent wiring is required, have a professional electrician install circuit and wire door operator. During the following steps, the motor protector may open. Remote control has less than 25 feet operating range.
Check the alignment of the two boxes one on either side of the door to assure they see each other and not the door as it comes down. Slide carriage toward door. Slide drive end of boom down over D-shaft on top of power head Fig. Posted on Aug 19, Mounting STB source and sensor.
Overhead Door CD Series Owner’s Manual
Insure that tops of lenses are between above the floor Fig. Can CauseSerious Injuryor DeathDo Not try to remove, repair or adjust springsor anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. How can this be resolved. Alternatively, you can delete the existing remotes from the unit and reprogram the remotes again, this will reprogram the emotes on a different frequency and hopefully cut out any interference.
Make sure they are pointed at one another and the small light on each one is not flickering ever so slightly. The outlet should be no more than about 3 feet from the power head once it is mounted.
Repairs and adjustments must be made by atrained service person using proper tools and instructions. Legcay to adjust the operator properly may cause severe injury or death. Tell us some more! This warranty gives you specific legal rights, and you may also have other rights which vary from nanual to state.
Garage door won’t close with remotes.
Have a qualified service person make repairs to cables, spring assemblies, and other hardware. Make sure the RPM sensor is plugged in. Each button on a multi-button remote control is for a different operator. Preventing crossed signals is critical. Never let children operate or play with operator controls. Answer questions, earn points and help others Answer questions. It loses power at random times.
Legacy CD-B Garage Door Opener Owners Manual
Do Not push the limit set switch again, yourlimits are set. It’s worth a thousand words. Make wire attachments at STBs. Legqcy operator will not close the door automatically unless the Safe-T-Beam System is installed. Relocate remote control inside car. Here’s a link to this great service Good luck! Check force adjustment See section7.
File:Legacy CD-B Owners – Wiki
Check lock switch on wall console See section 4. Do not use door operator or remote controls Refer to door and door operator owners Manuals before attempting any repairsNOTE: Determine door rise Fig. Your answer needs to include more details to help people. Overhead Door Company Documents. Claims under this warranty must be made in writing to ODC or one of its authorized distributors within the applicable warranty period.
Tweak them a little. That is most likely the limit sensor BUT it could be slippage. Factory sets different codes for each remotecontrol. Replace and tighten four 4 hex head screws.
Legacy 696CD-B Owners Manual
Be sure wire ends do not touch each otheror other terminals. When opening, door must not pass level position or if you are not able to close the door 696ccd completing previous step; a longer door arm is required.
If I give it a small slap it will turn back on, only to stop again from vibrations from movement. Install header bracket Fig. Want Answer 1 Clicking this will make more experts see the question and we will remind you when it gets answered.