Details, datasheet, quote on part number: MCT2E PARAMETER V(BR)CBO V( BR)CEO V(BRECO) IR IC(on) Collector-base breakdown voltage. IC MCT2E Optocouplers, datasheet and pin description. MCT2E price, Purchase MCT2E. The signal is applied to the LED, which then shines on the transistor in the IC. . The MCT2E series of opto-coupler devices each consist of gallium arsenide.

Author: Vimuro Shadal
Country: Liechtenstein
Language: English (Spanish)
Genre: Medical
Published (Last): 21 February 2014
Pages: 490
PDF File Size: 19.71 Mb
ePub File Size: 10.33 Mb
ISBN: 383-3-45334-971-2
Downloads: 82720
Price: Free* [*Free Regsitration Required]
Uploader: Maujas

The components are selected in such a way that the frequency output of the astable circuit lies within the audio range. The transistor gets base bias via phototransistor and resistor R6 R.

Astable mode of timer. Base pin of the Transistor. Clap switch December 18, Auto-Detection l Bluetooth l Smart Multimeter. How to use the DIY clap switch September 16, Light activated police siren using timer and light dependent resistor LDR. TL — Programmable Reference Voltage. HiFirst of allthank you for your circuit above. When switch S2 is pressed, the base of the transistor connects to the ground 0V and resets the timer bringing Pin 4 to LOW state.

This disables the alarm. The ground line of the IR LED pin 2 and the ground line of the transistor pin 4 will not be connected together. The complete working can also be understood form the GIF file above. The digital signal given to the IR LED will be reflected on the transistor but there will be no hard electrical connection between the two.

How to make one transistor FM transmitter on a stripboard- page Then Pull high the collector pin of the transistor using a resistor here I have used 1K and connect the collector pin to the output of your desired logic circuit. Building a circuit on a breadboard November 8, Digital object counter DIY kit September 1, From Latch up circuit using and optocouplerJuly 16, The NE timer is configured in astable mode.


How to use a relay November 15, I was wondering if you could help me with the following. This way the logic input will be reflected at the logic output and still provides and isolation between the two.

Tuesday, January 1, I made this project with another opto-coupler, PC and it works well. Connected to isolated ground. Opto-coupler, MCT2E is is used for latching the alarm.

IC MCT2E Optocouplers

When the IR led is powered the light from it falls on the transistor and it conducts. Review of PCBWay after-sale service. This is the logic output pin 6 Base B Base pin of the Transistor. But when the Logic input is made high, this high voltage should be a minimum of 1. It is normally not used for transistor mode, but will be used in diode mode.

Another important parameter to consider while using an Optocoupler, is the rise time tr and fall time tf. In the Photo-transistor mode we will not be using the base pin pin 6 of the transistor; we just have to connect the anode pin of the IR LED pin 1 to the logic input which has to be isolated and the cathode pin 2 of the IR led to the ground.

The Emitter pin 4 is grounded. The output will not get icc as soon as the input logic is made low and vice versa.


FREE timer simulators for electronics beginners. Submitted by admin on 7 March More details can be found at the MCT2E datasheet which is available for download at the end of this page. There pull-up resistor 1K acts as a load resistor. Kct2e is where the isolation occurs.

Invento 2pcs MCT2E IC – Optocoupler – 6 Pin DIP: : Industrial & Scientific

Blinker using arduino and NE mt2e IC. Easy steps for making a line following robot using Infrared LED, The sound remains ON till you press the reset switch S2. Out of which the Phototransistor mode is mostly used, so let us look at that iv first. This will short the collector and emitter and hence the Logic Output voltage will become zero. The below waveform shows the time taken for the output to transit from one state to another. Log into your account. How to make an FM transmitter January 26, Dark sensor on breadboard Mcf2e 8, How to use variable resistors November 15, How to use Mhz RF transmitter and receiver modules with arduino June 14, Toggle switch using This IC is used to provide electrical isolation between two circuits, one part of the circuit is connected to the IR LED and the other to Photo-transistor.

How to assemble infrared music transmitter and receiver DIY kit September 1,