ENDA ETC 9420 PDF

NOTE: ETC ENDA ETC series are intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding. Thank you for choosing ENDA EPC profile controller. * Selectable SSR or While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive. Double set point. Selectable sensor type (Pt, J, K, L, T, S, R). PID control function with accurate self-tuning. Digital inputs can be assigned to 3 different.

Author: Grogal Maucage
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Travel
Published (Last): 23 June 2004
Pages: 481
PDF File Size: 3.46 Mb
ePub File Size: 18.80 Mb
ISBN: 283-9-95944-594-1
Downloads: 68376
Price: Free* [*Free Regsitration Required]
Uploader: Kagis

The maximum value is the value of A1. If waited enough,the value increases at each step. Four kinds of functions can be selected. Adjusable between 1 and The maximum of C. Difference addresses should be selected for every device. Otherwise, Self-Tune should be activated. If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered. IP65 Rated population degree Rear panel: If band alarm is selected, A1.

These cables should not be close to the power cables or components. All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. The minimum value is the value of C. Then, the value is adjusted by using PV A1. SEt is the value of C. If independent or deviation alarm is selected, this parameter can be Lo. Process value during normal operation Mnemonic parameter code during programming SV Display: Before self tune procedure, A.

TOP Related Articles  TABLA SNELLEN EPUB DOWNLOAD

Technical Specification |

If this parameter is 1, digital filter runs most quick. While holding 25 REdY. IfInp parameter is selected TC or Pt, this parameter is seen. If the selected input type is changed, the value of C. If any key is pressed while P.

Enda ETC Series PID Temperature Controllers Panel Mount | Rapid Online

Use suitable compensation cables. Selectable, and The installation and electrical connections must be carried on by a qualified staff and must be according to the relevant locally applicable regulations. The same procedure is valid for the decrement key.

Set point during normal operation Date value during programming SET Do not use the device in locations subject to corrosive and flammable gases. Therefore, when using a grounding thermocouple, do not connect the logic output terminals to the ground. The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded.

The normal value is 0. CSET If key is pressed and held 0. Adjustable between 1 and If 0 is selected, soft start feature will be enable and the device reaches set point value quickly. Pay attention to the polarities of the thermocouple cables as shown in the figure right are connected to the. After PID is calculated A.

TOP Related Articles  COMPTABILITE ANALYTIQUE EPUB

It should be So the set point can be achieved by minimum fluctuations and in the shortest time. Enter PID parameters of the system if they are known at the begining. If the temperature unit is changed, the value of the UPL.

Enda ETC Series PID Temperature Controllers Panel Mount

If this parameter is set to 0, the output power becomes 0 at the set point. Set appears on the display. Press any key to deactivate the self-tune procedure.

If self tune is achieved A. It’s a community-based project which helps to repair anything. Selectable logic control output. UnIt Offset value is added to the ect value. Make sure that the device is used only for intended purpose.

The shielding must be grounded on the instrument side. If deviation alarm is selected, A1. When 2 wired Pt is used, terminals that are shown at the right of there must be short circuited for each product. When PID parameters are Filter for display rnda.

The value of parameter should be increased in interference. Then, the value is adjusted by using If C.

Relative humidity According to EN Front panel: If independent alarm is selected, A1.